 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| inductors spm3012 (3.2x3.0 mm) spm4012 (4.4x4.1 mm) spm5012 (5.4x5.1 mm) spm5030 (5.2x5.0 mm) SPM6530 (7.1x6.5 mm) may 2013 inductors for power circuits wound metallic magnetic material spm series
(1/24) inductors 001-01 / 20130527 / e531_spm.fm reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperatur e difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious d amage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders (2/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. inductors for power circuits wound metallic magnetic material features magnetic shield type wound inductor for power circuits using a metallic magnetic material. low-profile product lineup with max. heights of 1.2mm and 3.0mm allowing for different usages. compared to ferrite wound type inductors, it is possible to achieve large current, low rdc, and compactness. low inductance variance in high-temperature environm ents with good dc superi mposition characteristics. metallic magnetic material is used, and the structure has an integr ated molded coil, so hum noise is lower than with core adhes ive coils. application smart phones, tablet terminals, lapt op computers, hdds, servers, vrms, compact power supply modules, other part number construction operating temperature range, package quantity, product weight ?? operating temperature range includes self-temperature rise. ??? the storage temperature range is for after the circuit board is mounted. product compatible with rohs directive halogen-free compatible with lead-free solders overview of the spm series spm 3012 t - 1r0 m series name lwh dimensions packaging style inductance inductance tolerance (mm max.) (h) 3012 3.23.01.2 t taping 1r0 1.0 m 20% 4012 4.44.11.2 1r5 1.5 5012 5.45.11.2 2r2 2.2 5030 5.25.03.0 6530 7.16.53.0 spm 6530 t - r25 m 230 series name lwh dimensions packaging style inductance inductance tolerance internal code (mm max.) (h) 6530 7.16.53.0 t taping r25 0.25 m 20% 1r0 1.0 4r7 4.7 type temperature range package quantity individual weight operating temperature ? storage temperature ?? c c (pieces/reel) g spm3012 ?40 to +125 ?40 to +125 2000 0.047 spm4012 ?40 to +125 ?40 to +125 1000 0.0941 spm5012 ?40 to +125 ?40 to +125 1000 0.1500 spm5030 ?40 to +125 ?40 to +125 500 0.364 SPM6530 ?40 to +125 ?40 to +125 1000 0.656 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm. (3/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. overview of the spm series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 120s 230c 30s 260c 10s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature (4/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series spm3012 type shape & dimensions recommended land pattern 3.00.1 0.10.1 1.2max. 3.20.1 1.50.1 0.850.1 0.850.1 ( 1.5 ) dimensions in mm dimensions in mm 1.1 1.5 1.1 1.8 (5/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm3012 type electrical characteristics characteristics specification table ?? rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (30% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) measurement equipment ? equivalent measurement equipment may be used. l l measuring frequency (khz) dc resistance (m ? ) rated current(a) ? part no. max. typ. (h) tolerance max. typ. idc1 idc1 idc2 1.0 20% 100 65 57 3.4 5.4 2.8 spm3012t-1r0m 1.5 20% 100 90 77 2.8 4.7 2.5 spm3012t-1r5m 2.2 20% 100 115 100 2.5 3.4 2.2 spm3012t-2r2m 3.3 20% 100 210 183 1.8 2.8 1.5 spm3012t-3r3m 4.7 20% 100 270 232 1.5 2.6 1.3 spm3012t-4r7m measurement item product no. manufacturer l 4284a agilent technologies dc resistance ax-111a adex rated current idc1 4284a+42841a+42842c agilent technologies (6/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm3012 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 5.0 10.0 15.0 20.0 25.0 10 100 1000 10000 100000 ind u ct a nce ( h ) fre qu ency ( khz ) 4r7m 3 r 3 n 2r2n 1r5n 1r0n product no. manufacturer 4294a agilent technologies (7/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm3012 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0 1 2 4 3 5 ind u ct a nce ( h ) 012 3 456 dc c u rrent(a) 4r7m 3 r 3 m 2r2m 1r5m 1r0m product no. manufacturer 4284a+42841a+42842c agilent technologies (8/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series spm4012 type shape & dimensions recommended land pattern 0.10.1 1.2max. 2.00.1 4.10.2 4.40.2 0.90.1 0.90.1 ( 2.6 ) dimensions in mm dimensions in mm 1.65 1.65 1.65 2.3 (9/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm4012type electrical characteristics characteristics specification table ?? rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (30% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) measurement equipment ? equivalent measurement equipment may be used. l measuring frequency (khz) dc resistance (m ? ) rated current(a) ? part no. max. typ. (h) tolerance max. typ. idc1 idc1 idc2 0.47 20% 100 25 23 8.3 10.9 4.8 spm4012t-r47m 1.00 20% 100 45 38 4.8 6.0 4.1 spm4012t-1r0m 1.50 20% 100 70 59 3.5 4.8 3.1 spm4012t-1r5m 2.20 20% 100 95 82 3.3 4.4 2.7 spm4012t-2r2m 3.30 20% 100 145 123 2.8 3.5 2.2 spm4012t-3r3m 4.70 20% 100 205 178 2.0 2.5 1.7 spm4012t-4r7m measurement item product no. manufacturer l 4284a agilent technologies dc resistance ax-111a adex rated current idc1 4284a+42841a+42842c agilent technologies (10/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm4012type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 5.0 10.0 15.0 20.0 10 100 1000 10000 100000 ind u ct a nce ( h ) fre qu ency ( mhz ) 4r7m 3 r 3 m 2r2m 1r5m 1r0m 4r7m product no. manufacturer 4294a agilent technologies (11/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm4012type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0 1 2 4 3 5 0 2 4 6 8 10 12 dc current(a) 4r7m 3r3m 2r2m 1r5m 1r0m r47m product no. manufacturer 4284a+42841a+42842c agilent technologies (12/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series spm5012 type shape & dimensions recommended land pattern 0.10.1 1.2max. 2.50.1 5.10.2 1.20.1 1.20.1 ( 3.0 ) 5.40.2 dimensions in mm dimensions in mm 1.4 3.0 1.4 2.5 (13/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm5012 type electrical characteristics characteristics specification table ?? rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (30% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) measurement equipment ? equivalent measurement equipment may be used. l measuring frequency (khz) dc resistance (m ? ) rated current(a) ? part no. max. typ. (h) tolerance max. typ. idc1 idc1 idc2 1.00 20% 100 44.0 40.0 6.3 7.9 4.1 spm5012t-1r0m 2.20 20% 100 78.8 71.6 4.9 6.1 2.7 spm5012t-2r2m measurement item product no. manufacturer l 4284a agilent technologies dc resistance ax-111a adex rated current idc1 4284a+42841a+42842c agilent technologies (14/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm5012 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 2.0 4.0 6.0 8 .0 10 100 1000 10000 100000 ind u ct a nce ( h ) fre qu ency ( mhz ) 2r2m 1r0m product no. manufacturer 4294a agilent technologies (15/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm5012 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 1.0 0.5 2.0 2.5 1.5 3 .0 0246 8 10 dc c u rrent(a) ind u ct a nce ( h ) 2r2m 1r0m product no. manufacturer 4284a+42841a+42842c agilent technologies (16/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series spm5030 type shape & dimensions recommended land pattern 5.00.3 0.150.15 3.0max. 5.20.3 1.150.2 1.150.2 ( 2.9 ) r20 2.00.2 dimensions in mm dimensions in mm 2.2 1.5 2.7 1.5 2.2 (17/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm5030 type electrical characteristics characteristics specification table ?? rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (20% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) measurement equipment ? equivalent measurement equipment may be used. l measuring frequency (khz) dc resistance (m ? ) rated current(a) ? part no. typ. (h) tolerance max. typ. idc1 idc2 0.20 20% 100 2.31 2.1 21.0 22.2 spm5030t-r20m 0.35 20% 100 4.29 3.9 14.9 16.6 spm5030t-r35m 0.75 20% 100 9.35 8.5 9.7 11.3 spm5030t-r75m 1.0 20% 100 11.44 10.4 8.5 10.1 spm5030t-1r0m measurement item product no. manufacturer l 4284a agilent technologies dc resistance ax-111a adex rated current idc1 4284a+42841a+42842c agilent technologies (18/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm5030 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 0.5 1.0 1.5 2.0 10 100 1000 10000 100000 ind u ct a nce ( h ) fre qu ency ( mhz ) 1r0m r70m r 3 5m r20m product no. manufacturer 4294a agilent technologies (19/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y spm5030 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 0.2 0.4 1.0 0.6 0. 8 1.2 0 5 10 15 20 25 3 0 dc c u rrent(a) ind u ct a nce ( h ) 1r0m r75m r 3 5m r20m product no. manufacturer 4284a+42841a+42842c agilent technologies (20/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series SPM6530 type shape & dimensions recommended land pattern 6.50.3 0.150.15 3.0max. 7.10.3 1.550.3 1.550.3 ( 3.8 ) r25 3.20.3 dimensions in mm dimensions in mm 1.85 3.7 1.85 3.4 3.4 (21/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y SPM6530 type electrical characteristics characteristics specification table ?? rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (20% below the initial value) idc2: when based on the temperature increase (temperature increase of 40c by self heating) ~ the cleaning agent can not be used for these products. measurement equipment ? equivalent measurement equipment may be used. l measuring frequency (khz) dc resistance (m ? ) rated current(a) ? part no. typ. (h) tolerance max. typ. idc1 idc2 0.25 20% 100 2.31 2.1 28.5 23 SPM6530t-r25m230 0.47 20% 100 3.63 3.3 20.5 20 SPM6530t-r47m170 0.68 20% 100 5.39 4.9 16.6 16 SPM6530t-r68m140 1.0 20% 100 7.81 7.1 14.1 13 SPM6530t-1r0m120 1.5 20% 100 10.67 9.7 11.5 11 SPM6530t-1r5m100 2.2 20% 100 19 17.3 8.4 8.2 SPM6530t-2r2m 3.3 20% 100 29.7 27 7.3 6.8 SPM6530t-3r3m 4.7 20% 100 39.4 35.8 6.2 5.6 SPM6530t-4r7m measurement item product no. manufacturer l 4284a agilent technologies dc resistance ax-111a adex rated current idc1 4284a+42841a+42842c agilent technologies (22/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y SPM6530 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 5.0 10.0 15.0 20.0 3 0.0 25.0 10 100 1000 10000 100000 ind u ct a nce ( h ) fre qu ency ( mhz ) 4r7m 3 r 3 m 2r2m 1r5m 1r0m r47m r6 8 m r25m product no. manufacturer 4294a agilent technologies (23/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series y SPM6530 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.0 0.5 1.0 2.0 4.0 3 .0 1.5 2.5 4.5 3 .5 5.0 ind u ct a nce ( h ) 01020 3 04050 dc c u rrent(a) 4r7m 3 r 3 m 2r2m 1r5m 1r0m r47m r6 8 m r25m product no. manufacturer 4284a+42841a+42842c agilent technologies (24/24) inductors 001-01 / 20130527 / e531_spm.fm ? all specifications are subject to change without notice. spm series packaging style reel dimensions * these values are typical values. tape dimensions ty p e a b c d e spm3012 ?180 11.9 ?60 9.5 1.2 spm4012 ?180 14.4 ?60 12.4 1.0 spm5012 ?180 14.4 ?60 12.4 1.0 spm5030 ?180 14.4 ?60 12.4 1.0 SPM6530 ?330 20.4 ?100 16.4 2.0 e ?13.0 0.5 ?21.0 0.8 c b 2.0 0.5 a dimensions in mm ( 1.0 ) d fe w p0 p2 ?d0 p1 a0 t b0 k dimensions in mm ty p e a0 b0 ?d0 e f p0 p1 p2 w k t spm3012 3.2 3.4 1.5+0.1/-0 1.750.1 3.500.1 4.00.05 4.00.05 2.00.1 8.00.1 1.35 0.25 spm4012 4.35 4.65 1.5+0.1/-0 1.750.1 5.50.1 4.00.1 8.000.1 2.00.1 12.00.2 1.35 0.3 spm5012 5.4 5.7 1.5+0.1/-0 1.750.1 5.50.1 4.00.1 8.000.1 2.00.1 12.00.2 3.3 1.5 spm5030 5.3 5.5 1.5+0.1/-0 1.750.1 5.50.1 4.00.1 8.000.1 2.00.1 12.00.2 3.3 0.4 SPM6530 7.4 7.6 1.5+0.1/-0 1.750.1 7.50.1 4.00.1 12.00.1 2.00.1 16.00.3 3.6 0.4 |
Price & Availability of SPM6530
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |